Rabu, 26 Juni 2013

COMMISIONING MSAN HUAWEI


 






STEP KONFIGURASI MSAN



IPMB :
CONFIGURE SYSNAME, MANAGEMENT, ROUTING AND BOARD CONFIRM :
  1. CREATE SYSNAME
  2. MANAGEMENT CONFIGURATION (VLAN, INTERFACE, IP ADDRESS, AND PORT, STATIC ROUTING)
  3. CONFIGURE SNMP
  4. CREATE USERNAME
  5. CONFIRM BOARD
ADDING INTENET-BROADBAND SERVICE :
  1. CONFIGURE VLAN BROADBAND (VLAN SMART, AND PORT)
  2. CONFIGURE TRAFFIC TABLE
  3. CONFIGURE MULTI-SERVICE-PORT
  4. CONFIGURE ADSL LINE-PROFILE
  5. IN ADSL PORT è DEACTIVATE AND ACTIVATE WITH NEW LINE PROFILE
ADDING VoBB-VOICE OVER BROADBAND SERVICE
DiSesuai dengan Permintaan Telkom, Configurasi sama seperti CONFIGURASI BROADBAND
ALLOW VLAN H.248 and MEDIA :
  1. INTERFACE CONFIGURATION FOR H.248 DAN VOICE MEDIA (VLAN, AND PORT)
CONFIGURE EMU :
  1. CONFIGURE EMU

PVMB :
CONFIGURE SYSNAME, MANAGEMENT, ADD FRAME/BOARD, BOARD CONFIRM :
  1. CREATE SYSNAME
  2. MANAGEMENT CONFIGURATION
(IN THE INTERFACE ETH  è MODIFY IP ADDRESS, SUBMASK, GW, AND VLAN)
  1. CONFIGURE SNMP
  2. CONFIGURE WORKING MODE
  3. CREATE USERNAME
  4. ADD FRAME, BOARD, AND THEN BOARD CONFIRM
CREAT VLAN H.248 and MEDIA :
  1. CONFIGURE H.248 AND VOICE MEDIA
(IN THE INTERFACE ETH  è ADD IP ADDRESS, SUBMASK, GW, AND VLAN)
  1. CONFIGURE QoS FOR H.248 AND VOICE MEDIA
CONFIGURE INTERFACE VLAN H.248 and MEDIA :
  1. CONFIGURE IF-H.248
(USE IP MG, UDP PORT, IP MEDIA, IP SOFTSWITCH, NEGOTIATION AND MG NAME)
  1. CONFIGUR TID  è TID TEMPLATE FOR ZTE AND TID FORMAT RTP FOR NSN)
  2. RESET COLDSTART
CONFIGURE ESLUSER :
  1. CONFIGURE ESL USER (USE INNER DIGIT MAP)
CONFIGURE STAND ALONE :
  1. CONFIGURE EMERGENCY CALL
MANAGEMENT, NMS, and  IPMD (Broadband Control Board)
(Untuk Data IPMD MSAN, Perhatikan data pada BROADBAND masing2 DIVRE, dari File Excel MSAN)

NMS connection to N2000 BMS

sysname “MSAN00-(DIVRE)-(DATEL)-(MSAN-Vendor)<rk_name>”

Contoh Penggunaan :
MSAN HUAWEI Outdoor FRK pada Area Divre-7 Datel Bali
            Maka akan menjadi     sysname MSAN00-D7-BLI-2FRK
            Catatan : untuk No MSAN Vendor ; 1.NSN  2.HUAWEI  3.ZTE

Vlan 23 standard
port vlan 23  0/2 0,6-7

interface vlanif 23
ip address 172.29.180.13
quit

ip route-static 0.0.0.0 0.0.0.0 172.29.180.1

snmp-agent community read public
snmp-agent community write private
snmp-agent target-host trap address 172.29.128.4 securityname huawei v2c
snmp-agent target-host trap address 172.29.128.5 securityname huawei v2c
snmp-agent trap enable standard
snmp-agent trap source vlanif 23

Create additional admin user on IPMD board

Command:         terminal user name

  User Name(length<6,15>):admin
  The user name must be equal to or more than 6 characters
  User Name(length<6,15>):admin
  The user name must be equal to or more than 6 characters
  User Name(length<6,15>):admin123
  User Password(length<8,15>): r00tw3rk#@!
  Confirm Password(length<8,15>):
  User profile name(<=15 chars)[root]:
  User's Level:
     1. Common User  2. Operator  3. Administrator:3
  Permitted Reenter Number(0--4):4
  User's Appended Info(<=30 chars):working
  Adding user succeeds
  Repeat this operation? (y/n)[n]:n
Board confirmation on IPMD frame

UA5000-IPMD-50-test(config)#Board confirm 0

Contoh Penggunaan bila setelah di confirm masih belum terdeteksi :

UA5000-IPMD-50-test(config)#board add 0/10 ?
---------------------------------------------
  Command of config Mode:
---------------------------------------------
H601ADL               Parameter: Board name
H601ADLB              Parameter: Board name
H601ADLF              Parameter: Board name
H601ADRB              Parameter: Board name
H601AIUB              Parameter: Board name
H601CSL               Parameter: Board name
H601CSLB              Parameter: Board name
H601CSLC              Parameter: Board name
H601CSLI              Parameter: Board name
H601EAUA              Parameter: Board name
H601SDL               Parameter: Board name
H601SDLB              Parameter: Board name
H601TSSB              Parameter: Board name
H601TSSC              Parameter: Board name
H601VDL               Parameter: Board name
H602ADM               Parameter: Board name
H603ADR               Parameter: Board name
H603CSMC              Parameter: Board name
H603CSR               Parameter: Board name
H605CSR               Parameter: Board name
H612E1TF              Parameter: Board name
H612EFPF              Parameter: Board name
H612EFTF              Parameter: Board name
H612GAUA              Parameter: Board name
H612HLAF              Parameter: Board name
H612HLEF              Parameter: Board name
H612HLSF              Parameter: Board name
H612RATF              Parameter: Board name
H612SDLB              Parameter: Board name
H612SLPF              Parameter: Board name
H612SLTF              Parameter: Board name
H612SPLI              Parameter: Board name
H612TSTF              Parameter: Board name
H612WATF              Parameter: Board name


Note :
Bila setelah “Board Confirm 0” masih belum terlihat coba lakukan dengan manual 
Cara Manual è Pilih Type Board sesuai dengan Board yang terpasang pada slot yang akan di configure





Adding Internet Speedy service

Vlan 3004 smart
Port vlan 3004 0/2 0

traffic table index 7 ip car 1024 priority 0 priority-policy tag-In-Package
traffic table index 8 ip car 384 priority 0 priority-policy tag-In-Package

Note :  Traffic fisesuaikan dengan Up-Link,
Bila menggunakan FO “index 7 ip car 1024 “ dan “index 8 ip car 384”
                        Bila menggunakan VSAT “index 7 ip car 384 “ dan “index 8 ip car 64”

multi-service-port Vlan “Speedy (VLAN)”  board (Frame) (Board) vpi (VPI Number) vci (VCI Number) user-encap pppoe rx-cttr 7 tx-cttr 8

Contoh command :
After Create VLAN SMART and Port, Traffic Table, and Board Confirm
UA5000-IPMD-50-test(config)#multi-service-port Vlan 3004 board 0 6 vpi 0 vci 35 user-encap pppoe rx-cttr 7 tx-cttr 8

UA5000-IPMD-50-test(config)#multi-service-port Vlan 3004 board 0 6 vpi 0 vci 35 user-encap pppoe rx-cttr 7 tx-cttr 8


Keterangan command :
            Command diapply pada setiap Slot yang terinstall Board CSRB
Bila menggunakan FO “index 9 ip car 1024 “ dan “index 10 ip car 384”
Bila menggunakan VSAT “index 9 ip car 384 “ dan “index 10 ip car 64”
(Frame) => Frame MSAN yang sedang di konfigurasi
(Board)  => Board CSRB MSAN pada slot yang sedang di konfigurasi  
(VPI Number) dan (VCI Number) => sesuai ketentuan Telkom setempat
Contoh :
Divre2,5,6 menggunakan VPI 0 VCI 35, Divre-7(Makassar) menggunakan VPI 8 VCI 81

adsl line-profile quickadd 15 basic-para all trellis 1 bitswap 1 1 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 1024 32 384 name Speedy_1MHome

Keterangan command :
            15 è Merupakan Number Line Profile Speedy disesuaikan dengan permintaan Pihak Telkom
name Speedy_1MHome è Merupakan Line Profile Name sesuai permintaan Pihak Telkom
Bila menggunakan FO menggunakan “rate 32 1024 32 384
Bila menggunakan VSAT menggunakan rate 32 384 32 64

interface adsl 0/6
deactivate all
activate all profile-index 15
quit

Keterangan command :
            Command diapply pada setiap Slot yang terinstall Board CSRB
Adding Voice over BB (SIP Phone) service

vlan “VoBB (VLAN)”standard
port vlan “VoBB (VLAN)” 0/2 0

traffic table index 11 ip car 512 priority 7 priority-policy tag-In-Package
traffic table index 12 ip car 512 priority 7 priority-policy tag-In-Package

multi-service-port Vlan “VoBB (VLAN)” board (Frame) (Board) vpi (VPI Number) vci (VCI Number) user-encap pppoe rx-cttr 11 tx-cttr 12
Contoh command :
UA5000-IPMD-50-test(config)#multi-service-port Vlan 4000 board 0 6 vpi 1 vci 36 user-encap pppoe rx-cttr 11 tx-cttr 12

Keterangan command :
Command diapply pada setiap Slot yang terinstall Board CSRB
(Frame) => Frame MSAN yang sedang di konfigurasi
(Board)  => Board CSRB MSAN pada slot yang sedang di konfigurasi  
(VPI Number) dan (VCI Number) => sesuai ketentuan Telkom setempat

adsl line-profile quickadd 16 basic-para all trellis 1 bitswap 1 1 channel fast adapt at-startup snr 6 0 31 6 0 31 rate 32 1024 32 384 name Tripple_play

Keterangan command :
            16 è Merupakan Number Line Profile VoBB disesuaikan dengan permintaan Pihak Telkom
name Tripple_play è Line Profile Name VoBB
rate 32 1024 32 384  è Merupakan Downstream and Upstream MSAN terhadap subscribers

interface adsl 0/6
deactivate all
activate all profile-index 16
quit

Keterangan command :
            Command diapply pada setiap Slot yang terinstall Board CSRB
# if want to test VoBB, suggest to use ADSL2+ Home gateway that support port mapping on each FE port on the modem.


 Adding Vlan H.248 and Vlan Voice Media

vlan 1001 standard
port vlan 1001 0/2 0,6-7

vlan 2001 standard
port vlan 2001  0/2 0,6-7
EMU (Fan) pada MSAN Indoor-AC, Outdoor D200 , serta D500
(Cukup hanya di lakukan pada IPMD saja, silahkan copy-paste command2 berikut sesuai )



MSAN OUTDOOR D200

emu add 0 power4875 0 0 rs232 GEPS4875_MsanD200

interface emu 0
power battery parameter 0.18 60 1 80 
power battery temperature 60 -40 80
power charge voltage equalizing-voltage 56.5 floating-voltage 54.6
battery off permit 43.2
power environment temperature 50 0 55 -5
power environment humidity 80 10 95 0

power outside_digital 0 low-level MasterFrame_FAN
power outside_digital 2 high-level Battery_on_load
power outside_digital 3 low-level SPD_Failed
power outside_digital 4 high-level Smoke_Alarm
power outside_digital 5 high-level Heat_Exchanger
quit

emu add 1 power4875 0 0 rs232 GEPS4875_MsanD200
interface emu 1
power battery parameter 0.15 60 1 80
power battery temperature 60 -40 80
power charge voltage equalizing-voltage 56.5 floating-voltage 54.6
power off permit 43.2
power environment temperature 50 0 55 -5
power environment humidity 80 10 95 0
power outside-digital 0 low-level MasterFrame_FAN
power outside-digital 2 high-level Battery_on_load
power outside-digital 3 low-level SPD_Failed
power outside-digital 4 high-level Smoke_Alarm
power outside-digital 5 high-level Heat_Exchanger


MSAN OUTDOOR D500

emu add 0 power4875 0 0 rs232 GEPS4875_MsanD500

interface emu 1
power battery parameter 0.15 60 1 150 
power battery temperature 60 -40 80
power battery-test auto-discharge-permit 180 0 2 46
power charge voltage equalizing-voltage 56.5 floating-voltage 54.6
power off load-off-state permit load-off-voltage 44 battery-off-state permit battery-off-voltage 43.5
power environment temperature 50 0 55 -5
power environment humidity 80 10 95 0

power outside-digital 0 available-level low-level name MasterFrame_FAN
power outside-digital 2 available-level high-level name Battery_on_load
power outside-digital 3 available-level low-level name SPD_Failed
power outside-digital 4 available-level high-level Smoke_Alarm
power outside-digital 5 available-level high-level Heat_Exchanger
quit

MSAN INDOOR AC Cabinet

emu add 0 power4875 0 0 rs232 GEPS4875_MSANF02A

interface emu 1
power battery parameter 0.15 60 1 100 
power battery temperature 60 -40 80
power battery-test auto-discharge-permit 180 0 2 46
power charge voltage equalizing-voltage 56.5 floating-voltage 54.6
power off load-off-state permit load-off-voltage 44 battery-off-state permit battery-off-voltage 43.5
power environment temperature 50 0 55 -5
power environment humidity 80 10 95 0

power outside-digital 0 available-level low-level name MasterFrame_FAN
power outside-digital 2 available-level high-level name Battery_on_load
power outside-digital 3 available-level low-level name SPD_Failed
power outside-digital 4 available-level high-level Smoke_Alarm
power outside-digital 5 available-level high-level Heat_Exchanger
quit





NOTE : 

#
 Be aware that if IPMD is on the UA5000 frame, IPMD will have more priority controlling the EMU then PVMD.
 (Tidak disarankan melakukan configurasi via PVMD, HARUS via IPMD)
PVMD (Narrowband Control Board)
(Untuk Data PVMD MSAN, Perhatikan data pada NARROWBAND masing2 DIVRE, dari File Excel MSAN)

NMS connection to N2000 BMS

sysname “MSAN00-(DIVRE)-(DATEL)-(MSAN-Vendor)<rk_name>”    è  Sama seperti pada IPMD

#Konfigurasi Ethernet Ke-1 IP untuk Management/NMS

Interface eth
ip modify 10.10.10.2 ip_address 172.29.180.12 submask 255.255.255.192 gateway 172.29.180.1 vlan_tag 23
quit

Sebelum melakukan perubahan terlebih dahulu harus display status current interface :
UA5000-PVMD-Test(config)#display ip address  
  Eth:
  IPAddress............: 10.10.10.2        è  IP Eksisting
  SubMask..............: 255.255.255.0   
  GateWay..............: 10.10.10.1   
  MacIndex.............: 0   
  MacAddress...........: 00-25-9E-22-EE-F2   
  VlanID...............: --
Contoh :

Data ”NMS (IP & netmask)“ adalah 172.27.245.4/29 dengan “NMS (Gateway IP)“ adalah
172.27.245.1/29, dan “NMS (VLAN)” adalah Vlan 21,  Maka Printah akan menjadi :
UA5000-PVMD-Test(config)#Interface eth
UA5000-PVMD-Test(config)#ip modify 10.10.10.2 ip_address 172.27.245.4 submask 255.255.255.248 gateway 172.27.245.1 vlan_tag 21
UA5000-PVMD-Test(config)#quit
UA5000-PVMD-Test(config)#display ip address    
  Eth:
  IPAddress............: 172.27.245.4        è  IP sudah Berubah   
  SubMask..............: 255.255.255.248   
  GateWay..............: 172.27.245.1    
  MacIndex.............: 0   
  MacAddress...........: 00-25-9E-22-EE-F2   
  VlanID...............: 21

snmp-agent community read public
snmp-agent community write private
snmp-agent target-host trap address 172.29.128.4 securityname huawei v2c
snmp-agent target-host trap address 172.29.128.5 securityname huawei v2c
snmp-agent trap enable standard

autosave interval on
Working mode integrated
uplink tps on

Create additional admin user on PVMD board

Command:         terminal user name

  User Name(length<6,15>):admin
  The user name must be equal to or more than 6 characters
  User Name(length<6,15>):admin
  The user name must be equal to or more than 6 characters
  User Name(length<6,15>):admin123
  User Password(length<8,15>): r00tw3rk#@!
  Confirm Password(length<8,15>):
  User profile name(<=15 chars)[root]:
  User's Level:
     1. Common User  2. Operator  3. Administrator:3
  Permitted Reenter Number(0--4):4
  User's Appended Info(<=30 chars):working
  Adding user succeeds
  Repeat this operation? (y/n)[n]:n


Board confirmation on PVMD frame (indoor)

UA5000(config)#frame add 0          # adding the HABA main master frame
 FrameType:
    0 : MAIN_HABM_30(HABA)                      1 : MAIN_HAFM_30(HABD)
    2 : MAIN_HAFM_6(HABL)                       3 : MAIN_H602HABD(HABD)
    4 : MAIN_H601HABC(HABC)                     5 : SLAVE_HAFS_32(HABE)
    6 : SLAVE_HABS_32(HABB)                     7 : SLAVE_HABS_30(HABA)
    8 : SLAVE_HAFS_30(HABD)                     9 : SLAVE_H602HABD(HABD)
   10 : SLAVE_H602HABE(HABE)             11 : RSU_HAFS_30(HABD)
   12 : RSU_HABS_30(HABA)                13 : RSU_HAFS_12(HABC)
   14 : RSU_HAFS_6(HABL)                 15 : RSUG_ONU60A(HUBO)
   16 : RSUG_ONU04A                      17 : RSUG_ONU08A
   18 : RSP_19(HCB)                             19 : RSP_15(HDB)
   20 : RSP_14(HIB)                             21 : RSP_12(HFB)
   22 : RSP_10(HGB)                             23 : RSP_6A(HMB)
   24 : RSP_6B(HLB)                             25 : UAM_R (HUBM)
   26 : UAS_R (HUBS)                            27 : UAFM_R(HUBE)
   28 : UAFS_R(HUBF)                            29 : UAMB_R(HUBB)
   30 : ONU60A_R(HUBO)                   31 : ONUF01D100_R(HUBL)
   32 : VRSP_12(HABA)                    33 : VRSP_18(HABA)
   34 : HWTA(HIB_1)                             35 : HWTA(HIB_2)
   36 : HWTA(HIB_3)
Please select frame type (0 ~ 36): 0 (PILIH SESUAI FRAME YANG TERINSTALL)


Note :
Power-ON
Pastikan Indikator FAN dalam status Normal (Green-Blinking)
Pilih Frame sesuai dengan yang terinstal di site
Board confirmation on PVMD frame

UA5000-PVMD-Test(config)#Board confirm 0

Contoh Penggunaan :

UA5000-PVMD-Test(config)#board add 0/10 ?
---------------------------------------------
  Command of config Mode:
---------------------------------------------
A32                   32-port analog subscriber line board
ASL                   16-port analog subscriber line board
ATI                   Analog trunk interface board
CDI                   16-port direct dial-in subscriber interface board
CSM                   16-port analog subscriber line board
CSR                   32-port analog subscriber line board
DSL                   Digital subscriber line board
H301HWTA              Remote subscriber processing board
H601DSLD              16-port Digital subscriber line board
H601DSLE              16-port Digital subscriber line board
H601EDTB              16-port E1 conversion board
H601PVMD              Protocol processing and main node board
H602PWX               Secondary power board
H602RSUG              2-port G.SHDSL and 1-port E1 Remote subscriber H611SDLE              8-port G.SHDSL and 8-port E1 conversion board
H612EDTB              16-port E1 conversion board
HSL                   High speed synchronization line board
PWX2                  Secondary power board
PWX3                  Secondary power board
PWXA                  Secondary power board
RSP                   Remote subscriber processing board
RSU4                  4-port E1 Remote subscriber processing board
RSU8                  8-port E1 Remote subscriber processing board
SDL                   4-port G.SHDSL and 4-port E1 conversion board
TSS                   Subscriber test board
VFB                   Voice frequency board

Note :
Bila setelah memberikan “Board Confirm 0” masih belum terlihat, coba lakukan dengan manual 
Cara Manual è Pilih Type Board sesuai dengan Board yang terpasang pada slot yang akan di configure



frame connect 0 1      
# must connect the HW cable between HWCF to HWTF via HWOUT1 from HWCF and HWIN0 from HWTF.

# for HABD to HABF only need to connect HWOUT0 from HWCF from HABD to HWIN0 from HWTF on HABF extended frame. No need to add frame and connect it. Automatically HABD frame will have from 0-17 and 18-35 slots.



H.248 Voice over IP connection to Softswitch

#Konfigurasi Ethernet Ke-2 IP untuk IP H.248

Interface eth                           
ip address 172.29.160.8 255.255.255.192 172.29.160.1 vlan_tag 1001
quit


#Konfigurasi Ethernet Ke-3 IP untuk IP VOICE MEDIA

Interface eth                           
ip address 172.29.140.8 255.255.255.192 172.29.140.1 vlan_tag 2001
quit

Contoh Penggunaan :
Contoh data :
No.
Description (MSAN Outdoor)
Makassar_Mamasa
Narrowband

7
H248 (VLAN)
1001
8
H248 (IP & netmask)
172.29.160.69 /26
10
H248 Gateway IP
172.29.160.65 /26
11
Voice media (VLAN)
2001
12
Voice media (IP & netmask)
172.29.140.69 /26
13
Voice Gateway IP
172.29.140.65 /26

UA5000-PVMD-Test(config)# Interface eth                
UA5000-PVMD-Test(config)#ip address 172.29.160.69 255.255.255.192 172.29.160.65
vlan_tag 1001
UA5000-PVMD-Test(config)#quit
UA5000-PVMD-Test(config)# Interface eth                
UA5000-PVMD-Test(config)#ip address 172.29.140.69 255.255.255.192 172.29.140.65
vlan_tag 2001
UA5000-PVMD-Test(config)#quit

#Konfigurasi QoS pada Interface H.248

qos ip 172.29.160.8 strategy none
qos ip 172.29.160.8 strategy tos
qos ip 172.29.160.8 tos signalling 3 5

# Konfigurasi QoS pada Interface VOICE MEDIA

qos ip 172.29.140.8 strategy none
qos ip 172.29.140.8 strategy tos
qos ip 172.29.140.8 tos media 2 5

#Konfigurasi Interface H.248

interface h248 0
Are you sure to add MG interface?(y/n)[n]:y
if-h248 attribute mgip 172.29.160.8 (H248  mgport 2944 mg-media-ip 172.29.140.8 transfer udp mgcip_1 172.29.132.4 mgcport_1 “2944
if-h248 attribute start-negotiate-version 1 deviceName MSAN_Huawei
quit
           
Contoh Penggunaan  dengan contoh data :

No.
Description (MSAN Outdoor)
Makassar_Mamasa
Narrowband

8
H248 (IP & netmask)
172.27.245.12 /29
10
H248 Gateway IP
172.27.245.9 /29
12
Voice media (IP & netmask)
172.27.245.20 /29
13
Voice Gateway IP
172.27.245.17 /29
18
SS IP address (MGC_IP)
172.27.240.2 /29
19
SS UDP port MGC_port)
2944

UA5000-PVMD-Test(config)# interface h248 0
Are you sure to add MG interface?(y/n)[n]:y
UA5000-PVMD-Test(config)# if-h248 attribute mgip 172.27.245.12 mgport 2944 mg-media-ip 172.27.245.20 transfer udp mgcip_1 172.27.240.2 mgcport_1 2944
UA5000-PVMD-Test(config)# if-h248 attribute start-negotiate-version 1 deviceName MSAN_Huawei 
UA5000-PVMD-Test(config-if-h248-0)#display if-h248 attribute
  ---------------------------------------------------------------------
  MGID                                0      
  MG Description                      -              
  MG DomainName                       -              
  Protocol                            H248   
  H248version Negotiated Originally   1
  Profile Negotiation Para            disable
  Profile                             0:NoProfile("")                                                    
  2833Encrypt                         -               
  Codetype                            Text     
  Transmode                           UDP     
  HeartBeatTimer(s)                   60      
  HeartBeatRetransTimes               3   
  HeartBeatRetransTimer(s)            60  
  MG signalling IP                    172.27.245.12
  MG signalling Port                  2944    
  MG media IP                         172.27.245.20     
  MIDType                             IP4_ADDR            
  DeviceName                          MSAN_Huawei                                                      

  Active MGC       MGC Port       :2944          MGC IP: 172.27.240.2    
  Active MGC       MGC Domain Name:-              
  Standby MGC      MGC Port       :-             MGC IP:-              
  Standby MGC      MGC Domain Name:-               
  ---------------------------------------------------------------------

# Konfigurasi TID- Template dan TID-Format
 (HANYA DIGUNAKAN PADA MSAN YANG MENGINDUK KE SOFTWITCH ZTE)

interface h248 0
tid-template add 32 format %u parameter-list “TID-template format for temporary RTP” name “SoftSwitch type”
tid-format rtp template 32us
quit

Note :   IMPORTANT !!!
Harap di perhatikan bahwa kondisi default untuk TID-FORMAT pada MSAN-HUAWEI adalah :

UA5000-PVMD-Test(config)#interface h248 0
UA5000-PVMD-Test(config-if-h248-0)# display tid-template 1 
  -------------------------------------------------
  Index      : 1  
  Format     : %u                                                             
  Para-list  : R+100000001                                                     
  Name       : Rtp_No_Delamination            
  -------------------------------------------------

Maka untuk mengubah Parameter TID-FORMAT menjadi “R+65535” pada MSAN-HUAWEI adalah :

UA5000-PVMD-Test(config-if-h248-0)# tid-template add 32 format %u parameter-
list R+65535 name SS_ZTE
UA5000-PVMD-Test(config-if-h248-0)# display tid-template 32                                        
  -------------------------------------------------
  Index      : 32 
  Format     : %u                                                              
  Para-list  : R+65535                                                        
  Name       : SS_ZTE                          
  -------------------------------------------------
UA5000-PVMD-Test(config-if-h248-0)# display tid-format
  --------------------------------
  user-type template-index prefix
  --------------------------------
  rtp       32             A
  pstn      2              A
  bra       2              A
  pra       2              A
  r2        2              A
  dpnss     2              A
  dass2     2              A
  --------------------------------









# Konfigurasi Prefix TID- Template dan TID-Format
 (HANYA DIGUNAKAN PADA MSAN YANG MENGINDUK KE SOFTWITCH NSN)

Note :   IMPORTANT !!!
Harap di perhatikan bahwa kondisi default untuk TID-FORMAT pada MSAN-HUAWEI adalah :

UA5000-PVMD-Test(config)#interface h248 0
UA5000-PVMD-Test(config-if-h248-0)# display tid-format all 
  -------------------------------------------------
  MGID      user-type     template-index  prefix
  -------------------------------------------------
  0         RTP           1               A                      
  0         PSTN          2               A                      
  0         BRA           2               A                      
  0         PRA           2               A                      
  0         R2            2               A                      
  0         DPNSS         2               A                      
  0         DASS2         2               A                      
  -------------------------------------------------
UA5000-PVMD-Test(config-if-h248-0)# tid-format rtp prefix port_
UA5000-PVMD-Test(config-if-h248-0)# tid-format pstn prefix port_
UA5000-PVMD-Test(config-if-h248-0)# tid-format bra prefix port_
UA5000-PVMD-Test(config-if-h248-0)# tid-format pra prefix port_
UA5000-PVMD-Test(config-if-h248-0)# tid-format r2 prefix port_
UA5000-PVMD-Test(config-if-h248-0)# tid-format dpnss prefix port_
UA5000-PVMD-Test(config-if-h248-0)# tid-format dass2 prefix port_
UA5000-PVMD-Test(config-if-h248-0)# display tid-format all
  -------------------------------------------------
  MGID      user-type     template-index  prefix
  -------------------------------------------------
  0         RTP           1               port_                      
  0         PSTN          2               port_                  
  0         BRA           2               port_                  
  0         PRA           2               port_                   
  0         R2            2               port_                  
  0         DPNSS         2               port_                  
  0         DASS2         2               port_                  
  -------------------------------------------------


NOTE :
# Konfigurasi Prefix TID- Template dan TID-Format  PADA MSAN YANG MENGINDUK KE SOFTWITCH HUAWEI è TIDAK MENGALAMI PERUBAHAN SAMA SEKALI


# LAKUKAN RESET setelah selesai konfigurasi  H.248
UA5000-PVMD-Test(config)#interface h248 0
UA5000-PVMD-Test(config-if-h248-0)# reset coldstart                    #PILIH  è yes
UA5000-PVMD-Test(config-if-h248-0)# display if-h248 all             
#should be normal if already connected to SoftSwitch.


# Konfigurasi User H.248
KONFIGURASI INI HANYA BISA DIGUNAKAN BILA SUDAH DI PEROLEH RANGE NO.TELEPON DARI PIHAK TELKOM YANG AKAN DI INPUT PADA MSAN

Esl user
mgpstnuser batadd FrameA/BoardA/PortA FrameB/BoardB/PortB 0 terminalid 0 telno 42560000 step 1
quit

Contoh Penggunaan :
FrameA/BoardA/PortA dan FrameB/BoardB/PortB merupakan Board ASL, A32, dan CSRB
FrameA/BoardA/PortA  merupakan Board AWAL (Board ASL, A32, dan CSRB)
FrameB/BoardB/PortB merupakan Board AKHIR (Board ASL, A32, dan CSRB)
0   è   merupakan MGID
terminalid 0   è   merupakan START TID
step 1      è   merupakan jumlah penambahan nomer and TID sesuai jumlah step


Misal Pada sebuah Frame terdapat 4CSRB, 2A32, 3ASL.

Maka Jumlah Subscriber Narroband yang tersedia adalah : 128 + 64 + 48 = 240
4 CSRB = 4 * 32 = 128
2 A32  = 2 * 32 =  64
3 ASL  = 3 * 16 =  48
Telkom memberikan Nomer 7567000 à 7567239 :

Maka Commandnya Menjadi :
UA5000-PVMD-Test(config)# ESL user
UA5000-PVMD-Test(config-esl-user)# mgpstnuser batadd 0/6/0 0/14/15 0 terminalid 0 telno 7567000 step 1
UA5000-PVMD-Test(config-esl-user)# quit
UA5000-PVMD-Test(config-esl-user)# display mgpstn user 0/6

Configuring Inner Digitmap for emergency calling within the same MGID

interface h248 0
mg-software parameter 11 3
display mg-software parameter 11

            Contoh Penggunaan Command :
UA5000-PVMD-Test(config if-h248-0)# interface h248 0
UA5000-PVMD-Test(config if-h248-0)# mg-software parameter 11 3
UA5000-PVMD-Test(config if-h248-0)# display mg-software parameter 11
-------------------------------------------------
Interface Id:1 para index:11 value:3
-------------------------------------------------
APPENDIX:
-------------------------------------------------
Interface soft parameter name:
11: Stand alone support
0 : None
1 : Inner
2 : Emergency
3 : Both

standalone parameters dialtone 15 ring 60 busytone 50
display standalone parameters

            Contoh Penggunaan Command :
UA5000-PVMD-Test(config if-h248-0)# standalone parameters dialtone 15 ring 60 busytone 50
UA5000-PVMD-Test(config if-h248-0)# display standalone parameters
------------------------------------------------------------------
System stand alone para of timer for dial tone :15 (s)
System stand alone para of timer for busy tone :50 (s)
System stand alone para of timer for ring :60 (s)
------------------------------------------------------------------

digitmap set inner ”xxxxxxxx”
display digitmap

Note :   IMPORTANT !!! Jumlah inner digitmap diKoordinasikan dengan Technical Leader Huawei
            Contoh Penggunaan Command :
UA5000-PVMD-Test(config if-h248-0)# digitmap set inner ”xxxxxxxx”
UA5000-PVMD-Test(config if-h248-0)# display digitmap
------------------------------------------------------------------
Inner digitmap : xxxxxxxx
Emergency digitmap : -
Urgent digitmap (for overload or bandwidth restrict) : -
Dualdial digitmap for card service : -
------------------------------------------------------------------
UA5000-PVMD-Test(config if-h248-0)# quit
UA5000-PVMD-Test(config)#


Diposting oleh di

Tidak ada komentar:

Posting Komentar

Langganan: Posting Komentar (Atom)